|
C.G.Edwards & Co.Inc.
272 Dorchester Ave, P.O.Box 358 Boston, MA 02127 Phone: (617)268-4111-4112 * Fax:617-268-8845 E-mailwebsales@cgedwards.com |
|
Solid Flanged Bearings
Strut or Aft Stern Tubes Full Molded Type Johnson Cutless Flanged Type Water Lubricated Bearings are centrifugally cast naval brass with an integral flange for bolting to stern tube or strut housing to retain brearing and prevent rotation in housing. Specially formulated oil and chemical resistant nitrile rubber is securely bonded to the shell. Shells are heavy walled providing structural strength or step turned if desired. Precaution:When Shrink fitting of the bearing is required, Chilling must be achieved by gradual cooling to not more than minus 20°F (-28°C) using freezer or regular Ice.
Johnson Cutless Naval Brass Flanged Bearings meet
|
| Code | Shaft Diameter | Outside Diameter | Length | Flange Diameter | Flange Thickness | Metal I.D. | Metal Thickness |
| BRACE | 2" | 3" | 8" | 5" | 3/8" | 2-5/8" | 3/16" |
| BROAD | 2-1/2" | 3-3/8" | 10" | 5-1/2" | 3/8" | 3-1/8" | 1/8" |
| CATCH | 3" | 4-1/4" | 12" | 6-3/4" | 1/2" | 3-3/4" | 1/4" |
| CLAMP | 3-1/4" | 4-1/2" | 13" | 7" | 1/2" | 4" | 1/4" |
| CRANK | 3-1/2" | 4-3/4" | 12-1/2" | 6-3/4" | 1/2" | 4-1/4" | 1/4" |
| CLEAR | 3-1/2" | 4-7/8" | 14" | 7-3/8" | 1/2" | 4-1/4" | 5/16" |
| CIVIL | 3-3/4" | 5-1/4" | 15" | 7-3/4" | 1/2" | 4-5/8" | 5/16" |
| DRAFT | 4" | 5-1/2" | 16" | 8" | 1/2" | 4-7/8" | 5/16" |
| DREAD | 4-1/4" | 5-3/4" | 17" | 8-1/4" | 1/2" | 5-1/8" | 5/16" |
| DANCE | 4-3/8" | 6" | 22" | 8-7/8" | 1/2" | 5-3/8" | 5/16" |
| DRINK | 4-1/2" | 6" | 18" | 8-7/8" | 1/2" | 5-3/8" | 5/16" |
| DROVE | 4-3/4" | 6-1/4" | 19" | 9-1/8" | 1/2" | 5-3/8" | 5/16" |
| Code | Shaft Diameter | Outside Diameter | Length | Flange Diameter | Flange Thickness | Metal I.D. | Metal Thickness |
| EARTH | 5" | 6-3/4" | 20" | 9-5/8" | 9/16" | 6" | 3/8" |
| EASEL | 5-1/4" | 6-7/8" | 21" | 9-7/8" | 9/16" | 6-1/8" | 3/8" |
| ERASE | 5-1/2" | 7-1/4" | 22" | 10-1/4" | 9/16" | 6-1/2" | 3/8" |
| EVENT | 5-3/4" | 7-1/4" | 23" | 10-1/4" | 9/16" | 6-1/2" | 3/8" |
| FABLE | 6" | 7-3/4" | 15" | 12-1/4" | 9/16" | 6-1/2" | 3/8" |
| FAULT | 6" | 7-3/4" | 24" | 11" | 9/16" | 7" | 3/8" |
| FENCE | 6-1/4" | 8" | 22-1/2" | 10-5/8" | 9/16" | 7-1/8" | 3/8" |
| FLARE | 6-1/2" | 8-3/8" | 23-1/2" | 11" | 9/16" | 7-3/8" | 7/16" |
| FLEET | 6-1/2" | 8-3/8" | 30" | 11" | 5/8" | 7-1/2" | 7/16" |
| FLUTE | 6-5/8" | 8-1/2" | 15" | 13-1/2" | 5/8" | 7-1/2" | 7/16" |
| FLOOR | 6-5/8" | 8-1/2" | 24" | 11-1/4" | 9/16" | 7-5/8" | 7/16" |
| FRANK | 6-5/8" | 8-5/8" | 24" | 11-1/4" | 9/16" | 7-5/8" | 3/8" |
| FROZE | 6-3/4" | 8-3/4" | 24" | 11-1/4" | 5/8" | 7-7/8" | 7/16" |
| Code | Shaft Diameter | Outside Diameter | Length | Flange Diameter | Flange Thickness | Metal I.D. | Metal Thickness |
| FANCY | 6-3/4" | 8-3/4" | 24-1/2" | 11-3/8" | 9/16" | 7-7/8" | 7/16" |
| FOUND | 6-7/8" | 8-7/8" | 24-1/2" | 11-3/8" | 9/16" | 7-7/8" | 1/2" |
| GAVEL | 7" | 9" | 25-1/2" | 11-5/8" | 9/16" | 8-1/8" | 7/16" |
| GLAND | 7" | 9-1/8" | 25-1/2" | 11-5/8" | 9/16" | 8-1/8" | 1/2" |
| GLASS | 7-1/4" | 9-1/4" | 26-1/2" | 11-7/8" | 9/16" | 8-3/8" | 7/16" |
| GLORY | 7-1/2" | 9-5/8" | 17-1/2" | 14-1/2" | 1" | 8-3/4" | 7/16" |
| GLOBE | 7-1/2" | 9-5/8" | 27-1/2" | 12-3/4" | 9/16" | 8-3/4" | 7/16" |
| GIPSY | 7-3/4" | 9-7/8" | 28-1/2" | 12-1/2" | 9/16" | 8-7/8" | 1/2" |
| HEART | 8" | 10-1/4" | 29-1/2" | 13-1/4" | 5/8" | 9-1/2" | 1/2" |
| HEDGE | 8" | 10-1/2" | 29-1/2" | 13-1/4" | 5/8" | 9-1/2" | 1/2" |
| HITCH | 8-1/4" | 10-1/2" | 30-1/2" | 13-1/2" | 5/8" | 9-1/2" | 1/2" |
| HOIST | 8-1/2" | 10-3/4" | 31-1/2" | 13-3/4" | 5/8" | 9-3/4" | 1/2" |
| HOVER | 8-3/4" | 11" | 32-1/2" | 14" | 5/8" | 10" | 1/2" |
| Code | Shaft Diameter | Outside Diameter | Length | Flange Diameter | Flange Thickness | Metal I.D. | Metal Thickness |
| INFRA | 9" | 11-1/4" | 33-1/2" | 14-1/4" | 3/4" | 10-1/4" | 1/2" |
| IDEAL | 9" | 11-1/2" | 33-3/8" | 15" | 3/4" | 10-1/4" | 5/8" |
| INNER | 9-1/8" | 11-1/2" | 34-1/2" | 16-3/8" | 5/8" | 10-3/8" | 9/16" |
| IRISH | 9-1/4" | 11-1/2" | 34-1/2" | 14-5/8" | 11/16" | 10-1/2" | 1/2" |
| INSET | 9-1/2" | 11-3/4" | 35-1/2" | 14-7/8" | 3/4" | 10-3/4" | 1/2" |
| IVORY | 9-3/4" | 12-1/8" | 36-1/2" | 15-1/4" | 3/4" | 11" | 9/16" |
| JEWEL | 10" | 12-3/8" | 37-1/2" | 15-1/2" | 3/4" | 11-1/4" | 9/16" |
| JETTY | 10-1/4" | 12-5/8" | 38-1/2" | 15-7/8" | 3/4" | 11-1/2" | 9/16" |
| JUMBO | 10-1/2" | 12-7/8" | 39-1/2" | 16-1/8" | 3/4" | 11-3/4" | 9/16" |
| JUDGE | 10-3/4" | 13-1/8" | 40-1/2" | 16-3/8" | 3/4" | 12" | 9/16" |
| KNOCK | 11" | 13-1/2" | 41-1/2" | 17-1/4" | 3/4" | 12-3/8" | 9/16" |
| KRAFT | 11-1/4" | 13-3/4" | 42-1/2" | 17-1/2" | 3/4" | 12-5/8" | 9/16" |
| KNEEL | 11-1/2" | 14-1/8" | 43-1/2" | 17-7/8" | 3/4" | 12-7/8" | 5/8" |
| KNIFE | 11-1/2" | 14-7/8" | 50-3/4" | 20-1/4" | 1-1/4" | 12-7/8" | 1" |
| Code | Shaft Diameter | Outside Diameter | Length | Flange Diameter | Flange Thickness | Metal I.D. | Metal Thickness |
| KNOTS | 11-3/4" | 14-3/8" | 44-1/2" | 18-1/8" | 3/4" | 13-1/8" | 5/8" |
| LABOR | 12" | 14-3/4" | 45-1/2" | 18-1/2" | 3/4" | 13-1/2" | 5/8" |
| LOGAN | 12-1/8" | 14-7/8" | 46" | 18-5/8" | 3/4" | 13-5/8" | 5/8" |
| LANCE | 12-1/4" | 15" | 46-1/2" | 18-3/4" | 3/4" | 13-3/4" | 5/8" |
| LEASE | 12-3/8" | 15-1/8" | 47" | 18-7/8" | 3/4" | 13-7/8" | 5/8" |
| LAYER | 12-1/2" | 15-3/4" | 47-1/2" | 19" | 3/4" | 14" | 5/8" |
| LOGIC | 12-5/8" | 15-3/8" | 48" | 19-1/8" | 3/4" | 14-1/8" | 5/8" |
| MILKY | 12-3/4" | 15-1/2" | 48-4/8" | 19-1/4" | 3/4" | 14-1/4" | 5/8" |
| MUSIC | 12-7/8" | 15-5/8" | 49" | 19-3/8" | 3/4" | 14-3/8" | 5/8" |
| MINCE | 13" | 15-7/8" | 50" | 19-5/8" | 7/8" | 14-1/2" | 11/16" |
| MITTY | 13-1/8" | 16" | 50-1/2" | 19-3/4" | 7/8" | 14-5/8" | 11/16" |
| MISTY | 13-1/4" | 16-1/8" | 51" | 19-7/8" | 7/8" | 14-3/4" | 11/16" |
| Code | Shaft Diameter | Outside Diameter | Length | Flange Diameter | Flange Thickness | Metal I.D. | Metal Thickness |
| NIFTY | 13-3/8" | 16-1/4" | 51-1/2" | 20" | 7/8" | 14-7/8" | 11/16" |
| NIECE | 13-1/2" | 16-3/8" | 52" | 20-1/8" | 7/8" | 15" | 11-16" |
| NOVEL | 13-5/8" | 16-1/2" | 52-1/2" | 20-1/4" | 7/8" | 15-1/8" | 11/16" |
| ORTHA | 13-3/4" | 16-5/8" | 53" | 20-3/8" | 7/8" | 15-1/4" | 11/16" |
| OGGLE | 13-7/8" | 16-3/4" | 53-1/2" | 20-1/2" | 7/8" | 15-3/8" | 11/16" |
| OPERA | 14" | 16-7/8" | 54" | 20-5/8" | 7/8" | 15-1/2" | 11/16" |
| PURSE | 14-1/8" | 17" | 54-1/2" | 20-3/4" | 7/8" | 15-5/8" | 11/16" |
| POLAR | 14-1/4" | 17-1/8" | 55" | 20-7/8" | 7/8" | 15-3/4" | 11/16" |
| POINT | 14-3/8" | 17-1/4" | 55-1/2" | 21" | 7/8" | 15-7/8" | 11/16" |
| PRUNE | 14-1/2" | 17-1/2" | 56" | 21-1/4" | 7/8" | 16" | 11/16" |
| PRICE | 14-5/8" | 17-5/8" | 56-1/2" | 21-3/8" | 7/8" | 16-1/8" | 11/16" |
| PUNCH | 14-3/4" | 17-3/4" | 57" | 21-1/2" | 7/8" | 16-1/4" | 11/16" |
| Code | Shaft Diameter | Outside Diameter | Length | Flange Diameter | Flange Thickness | Metal I.D. | Metal Thickness |
| QUAKE | 14-7/8" | 17-7/8" | 57-1/2" | 21-5/8" | 7/8" | 16-3/8" | 11/16" |
| QUIET | 15" | 18" | 58" | 21-3/4" | 7/8" | 16-1/2" | 11/16" |
If you would like a price quote on any of these items, please fill out the form below
If you would like to check the status of an order,
All Images and logo's on this website are copyrighted and may not be reproduced without permission
Click here
Contact C.G. Edwards
Return to C.G. Edwards Homepage
This site last updated September 21, 2003
