Amerlock 400 high solids epoxy coatings

Amerlock 400 Product Data Low VOC High-performance general maintenance coating for new or old steel Cures through wide temperature range Self-priming topcoat over most existing coatings Can be overcoated with wide range of topcoats Compatible with prepared damp surfaces Compatible with adherent rust remaining on prepared surfaces 5 mils or more in a single coat Resists high humidity and moisture Temperature resistance to 450°F on insulated or uninsulated surfaces when mixed with Amercoat 880 glass flake additive Can be applied to substrates with temperatures up to 250°F VOC Amerlock 400 lb/gal g/L mixed 1.5 180 mixed/thinned (1/2 pt/gal) 1.8 220 VOC Amlerlock 400AL lb/gal g/L mixed 1.0 120 mixed/thinned (1-1/2 pt/gal) 2.0 240 Volume solids (ASTM D2697 modified)     Amerlock 2 83% ± 3% Amerlock 2AL 88% ± 3% Amerlock’s low solvent level meets VOC requirements, reduces the chances for film pinholing and solvent entrapment at the substrate-coating interface, often a major cause of coating failure with conventional epoxies and lower solids systems. Amerlock 400 is available in a variety of colors, including aluminum, and therefore does not require a topcoat. For extended weatherability or special uses, a topcoat may be desired. Typical Uses Amerlock 400 is used in those areas where blasting is impractical or impossible. As a maintenance coating, Amerlock 400 protects steel structures in industrial facilities, bridges, tank exteriors, marine weathering, offshore, oil tanks, piping, roofs, water towers and other exposures. Amerlock 400 has good chemical resistance to splash/spillage, fumes and immersion in neutral, fresh and salt water (see resistance table). Contact your PPG representative for specific information. Qualifications USDA – Incidental food contact NFPA – Class A NSF Standard 61 – For use in drinking water. Recommended Thinners Amercoat 65 Amercoat 101 Recommended Cleaner Amercoat 12 or Thinner Click here for Product Data Sheets (page will open in new window)

Amerloc 400 VOC Product Data Low VOC - compliant with SCAQQMD rule 1113 High performance general maintenance coating for old or new steel Cures through wide temperature range Self priming topcoat over most existing coatings Can be overcoated with a wide range of topcoats Compatable with prepared damp surfaces Compatable adherant rust remaining on prepared surfaces 5 mils or more in a single coat Resists high humidity and moisture Temperature resistance to 450°F on insulated or uninsulated surfaces when mixed with 88 glass flake additive Amerlock's low solvent level meets VOC requirements, reduces the chances for film pinholing and solvent entrapment at the substrate-coating interface. VOC (EPA method 24) lb/gal g/L mixed 0.82 98 Volume solids (ASTM D2697 modified) 83% ± 3% Typical Uses Amerlock 400 VOC is used in those areas where blasting is impractical or impossible. As a maintenance coating, Amerlock 400 VOC protects steel structures in industrial facilities, bridges, tank exteriors, marine weathering, offshore, oil tanks, piping, roofs, water towers and other exposures. Amerlock 400 VOC has good chemical resistance to splash/spillage, fumes, and immersion in neutral, fresh and salt water. Qualifications USDA - Incidental food contact NFPA - Class A Systems using Amerlock 400 VOC Amerlock 400 VOC - - Amerlock 400 VOC Amerlock 400 VOC - Amerlock 400 VOC Amershield - Dimetcoat 21-5 Amerlock 400 VOC Amershield Recommended Thinners Amercoat 65 Amercoat 101 Amercoat 8 Recommended Cleaner Amercoat 12 or Thinner Click here for Product Data Sheets (page will open in new window)