C.G.Edwards & Co.Inc.

272 Dorchester Ave, P.O.Box 358
Boston, MA 02127
Phone: (617)268-4111-4112 * Fax:617-268-8845
Email: websales@cgedwards.com



images/westlogo.gif - 1977 Bytes

Epoxy Products

This Versitile,high quality epoxy can be modified to provide a wide range of
handling characteristics and physical properties, creating the
ideal for your coating and bonding applications.





105 Resin

105.jpg - 3232 Bytes
105 Epoxy Resin
105 Epoxy Resin® is the base material on which all West System 105 System epoxy compounds are built. The resin is a clear, pale yellow, low-viscosity liquid epoxy resin. Formulated for use with West System hardeners, it can be cured in a wide temperature range to form a high-strength solid with excellent moisture resistance.

105 Resin is formulated without volatile solvents and does not shrink after curing. It has a relatively high flash point and no strong solvent odor, making it safer to work with than polyester or vinylester resins. Resin viscosity is approximately 1000 centipoise (cp) at 72 F (22C),

105 Resin is designed specifically to wet out and bond with wood fiber, fiberglass, reinforcing fabrics and a variety of metals when mixed at the proper ratio with a West System hardener. An excellent adhesive, 105 mixtures will bridge gaps and fill voids when modified with West System fillers and can be sanded and shaped when cured. With roller applications, it has excellent thin-film characteristics to flow out and self-level without "fisheyeing." 105 Resin/207 Hardener mixtures cure clear so you can achieve a natural finish when coating with varnish.

55 gallon drums available upon request, call for pricing and availability

Group A, 1 Quart Resin $ 39.95
Group B, 1 Gallon Resin $ 84.95
Group C, 4.35 Gallon Resin $ 329.95


Hardeners

205.jpg - 3466 Bytes
205 Fast Hardener
205 Fast Hardener is formulated for general coating and bonding applications at lower temperatures and to produce a rapid cure that develops its physical properties quickly at room temperature. 105/205 forms a high strength, moisture-resistant solid with excellent bonding and barrier coating properties.

Not intended for clear coating.

Pot Life at 72° F 9-12 min.
Cure Time at 72° F 6-8 hours
Minimum Working Temperature 40° F
Group A Fast Hardener $ 16.95
Group B Fast Hardener $ 37.50
Group C Fast Hardener $ 129.95


206.jpg - 3447 Bytes
206 Slow Hardener
206 Slow Hardener is formulated for general coating and bonding applications when extended working and cure time are needed or to provide adequate working time at higher temperatures.
105/206 forms a high-strength, moisture-resistant solid with excellent bonding and barrier coating properties.

Not intended for clear coating.

Pot Life at 72° F 20-25 min.
Cure Time at 72° F 9-12 hours
Minimum Working Temperature 65° F
Group A Slow Hardener $ 16.95
Group B Slow Hardener $ 37.50
Group C Slow Hardener $ 129.95




Special Ratio Hardeners

207.jpg - 3967 Bytes
207 Special Coating Hardener
207 Special Clear Hardener was developed for coating and fiberglass cloth application where an exceptionally clear, moisture-resistant, clear carbon fiber or natural wood finish is desired. 207 Hardener will not blush or turn cloudy in humid conditions. Thin film applications roll out and tip off smoothly, requiring less sanding in preparation for finish coatings.
Professional and first-time builders like 207 because it is reliable and easy to use. Three coats or more can be applied in one day without additional surface preparation. Fewer coats are required to fill fiberglass weave and in most cases the final coating can be sanded the following day. Builders also appreciate the excellent fiberglass wet-out characteristics achieved with 105/207, yet it won’t drain from vertical surfaces like the very slow curing, low-viscosity epoxies.

105/207 has strong physical properties, so it can be used as a structural adhesive for gluing and laminating. It has excellent compatibility with paints and varnishes. An ultraviolet inhibitor in 207 helps provide a beautiful, long lasting finish when used with quality UV-filtering top coat.

Pot Life at 72° F 20-25 min.
Cure Time at 72° F 9-12 hours
Minimum Working Temperature 60° F
Group A Special Coating Hardener $ 33.95
Group B Special Coating Hardener $ 72.95
Group C Special Coating Hardener $ 234.95


209.jpg - 3808 Bytes
209 Extra Slow Hardener
209 Extra Slow Hardener is formulated for general coating and bonding applications in extremely warm and/or humid conditions or when extended working time is desired at room temperature. Provides approximately twice the working time of 206 Slow Hardener.

105/209 forms a high-strength, moisture-resistant solid with excellent bonding and barrier coating properties.

Not intended for clearcoating

Pot Life at 95° F 40-50 min.
Cure Time at 95° F 20-24 hours
Minimum Working Temperature 70° F
Group A Extra Slow $ 29.50
Group B Extra Slow $ 65.50
Group C Extra Slow $ 213.50


Pump Sets

303.jpg - 3057 Bytes
300 Mini-Pumps
300 Mini Pumps are designed for convenient and accurate metering of all Group Size A, B and C WEST SYSTEM resin and hardeners.
They mount directly on the resin and hardener containers and eliminate the mess involved with measuring by weight or volume.
300 Mini Pumps are calibrated to deliver the proper working ratio with one full pump stroke of resin for each one full pump stroke of hardener.
300 dispensing pump $ 12.95


303.jpg - 3057 Bytes
320 Small Batch Epoxy Scale
For batches smaller than one Mini Pump stroke, the 320 scale accurately measures the correct ratio of resin and hardener from 4.4 fl oz down to just a few drops.
The scale can also be used to confirm the accuracy of your WEST SYSTEM dispensing pumps and to consistently add pigments or other additives.
The scale comes in a convenient kit for small projects. The kit includes dispensing bottles, 3¼ oz and 1 oz plastic mixing cups, mixing sticks and pipe cleaners
320 Small Batch Scale $ 44.95

High Capacity Gear Pumps
Call for Pricing



306 Model A Dispensing Pump
306-25 METERING PUMP
For metering larger quantities of 105 Resin and 205 or 206 (5:1 ratio) Hardeners.
The 306-25 Pump will reduce mixing time and waste on large projects.
A carrying handle allows you to move the pump where the work is.
Reservoirs hold one gallon of resin, one quart of hardener. Dispenses approximately 0.5 fl oz of resin/hardener per pump stroke (about 1 qt per minute).
Can be converted to a 3:1 ratio.

306-23 METERING PUMP
Similar to 306-25 Metering Pump described above. For metering 105 Resin and 207 Special Coating or 209 Extra Slow (3:1 ratio) Hardeners.
Can be converted to a 5:1 ratio.

 

303 POSITIVE DISPLACEMENT PUMP (3:1) This positive displacement metering pump dispenses three parts resin to one part hardener by volume.
It consists of two separate parallel pump systems, one for the resin and one for the hardener.
The two systems are operated simultaneously by a single lever. The pump delivers 2.3 fl. oz. of resin and hardener per full stroke of the dispensing lever.
The reserviors hold two gallons of resin and one gallon of hardener. Red Base.
For use with 207 Special Clear or 209 Extra Slow (3:1 ratio) Hardeners.

305 POSITIVE DISPLACEMENT PUMP (5:1)
Similar to 303 Positive Displacement Pump described above, the 305 pump is designed to accurate dispense WEST SYSTEM resins and hardeners at 5:1 by volume. Blue Base.
For use with 205 Fast or 206 Slow (5:1 ratio) Hardeners.


Repair Packs

101-6.jpg - 5232 Bytes
101 Handy Repair Pack
For small repairs around your boat, shop or home.
Contains two 105 resin/205 hardener packets, high density filler, an application brush, mixing stick, pipe cleaner, and instructions
$ 15.95
101-6 Maxi Repair Pack
Contains six 105 resin/205 hardener packets, low density filler for fairing and high density filler for bonding.
Includes two application brushes, one syringe, two pipe cleaners, four mixing sticks, mixing cups and illustrated instructions.
$ 35.95
101T resin/hardner packets
Contains 6 packets of pre-measured 105 resin/205 hardener
$ 25.95


G-5 Adhesive

865.jpg - 4137 Bytes
An easy to use, 2-part resin/hardener system for quick repairs, tooling and general bonding. May be used in spot applications to hold parts in position while standard epoxy bonds cure.
Bonds to wood, fiberglass and metal.
Not recommended for long-term bonds subject to high loads or moisture.
One-to-one mixture, no pumps are required.
Cures in 3-5 minutes.
 
G5 adhesive, 2 4oz bottles $ 21.95
G5 adhesive, 2 16 oz bottles $ 59.95


 

G/Flex Epoxy

650.jpg - 4137 Bytes
A toughened, versatile, liquid epoxy for permanent waterproof bonding of fiberglass, ceramics, metals, plastics, damp and difficult-to-bond woods. With a modulus of elasticity of 150,000 PSI, it is a bit more flexible than standard epoxies and polyester, but much stiffer than adhesive sealants.
This gives G/flex 650 the ability to make structural bonds that can absorb the stress of expansion, contraction, shock, and vibration.
It is ideal for bonding dissimilar materials. It can be modified with West System fillers and additives, and used to wet-out fiberglass tapes and fabrics.
Mixed at a 1:1 ratio, G/flex 650 gives you 45 minutes of working time at 72°F. It reaches an initial cure in 7 to 10 hrs and full cure in 24 hrs. (8 fl. oz. / 236 mL)
 
G/Flex epoxy, 8 ounce kit $ 21.95
G/Flex epoxy, 32 ounce kit $ 64.95
G/Flex epoxy, 2 gallon kit $ 294.95
 

G/Flex Epoxy Repair Kit
This kit contains 4 fl. oz. G/flex 650 resin, 4 fl. oz. G/flex 650 hardener (8 fl. oz. mixed epoxy), 2 reusable mixing stick/applicators, 2 12-cc syringes, 4 grams Adhesive Filler, 4 mixing cups, 1 pair disposable neoprene gloves, and complete handling and repair instructions.

G/flex epoxy, $ 32.95


 

G/Flex Thickend Epoxy

650.jpg - 4137 Bytes
 

G/Flex Thickened Epoxy Adhesive
A toughened, versatile epoxy that is conveniently pre-thickened for permanent waterproof bonding of plastic, fiberglass, ceramics, metals, damp and difficult-to-bond woods.
With a modulus of elasticity of 150,000 PSI, it is a bit more flexible than standard epoxies and polyester, but much stiffer than adhesive sealants.
This gives G/flex 655 the ability to make structural bonds that can absorb the stress of expansion, contraction, shock, and vibration.
It is ideal for bonding dissimilar materials. Mixed at a 1:1 ratio, G/flex 655 gives you 45 minutes of working time at 72°F. It reaches an initial cure in 7 to 10 hrs and full cure in 24 hrs. (8 fl. oz. / 250 mL)

G/Flex epoxy, 16 Ounce kit $ 24.95
G/Flex epoxy, 2 quart kit $ 84.95
G/Flex epoxy, 2 gallon kit $ 329.95
 

G/Flex Plastic Boat Repair Kit
Repair plastic canoes, kayaks, and inflatables made from HDPE, LDPE, ABS, PVC or polycarbonate plastic with the contents of this kit.
The Plastic Boat Repair Kit features plastic-friendly G/flex epoxy, and is assembled with the do-it-yourselfer in mind.
Each Plastic Boat Repair Kit contains 8.4 ounces of pre-thickened G/flex epoxy, protective gloves, mixing pallets and mixing sticks.
Illustrated, detailed instructions explain how to repair splits and cracks in plastic boats, attach or repair reinforcement points on inflatable boats and repair pinhole leaks in inflatables.

G/Flex Epoxy Repair Kit $ 32.95

 

Please Note:
With all the recent cases of on-line credit card and Identity theft,
we feel obliged to inform our customers that neither
C.G. Edwards Co Inc. or Boxell's Chandlery,
under any circumstance sell or divulge any personal information about our customers,
nor do we in any way store confidential information on our server.
Please be assured that we will continue to do everything within our power to keep any
information submitted by our customers as secure as we possibly can.

Please select the products and/or enter the number of units required. On JavaScript-enabled browsers the display table will be automatically updated. Such display is for information only and is not essential for the operation. You can select any number of items prior to adding to the shopping cart. It is not necessary to add each item to the cart as they are selected. However, if the products are in the form of a simple or dropdown list, and JavaScript is NOT enabled, then you must add each item to the cart individually.

Current Selection
The following information is generated automatically for display only. Tax and delivery may be changed.
Total value ($) Choose Tax rate(%)
 
Sub total ($)
 


Contact C.G. Edwards
Contact C.G. Edwards


Return to West Index

hpbutton.jpg - 1591 Bytes
Return to C.G. Edwards Homepage

This page updated July 21, 2017

All Images and logo's on this website are copyrighted and may not be reproduced without permission